{"product_id":"matek-crossfire-to-pwm-converter-crsf-pwm-6","title":"Matek Crossfire to PWM Converter - CRSF PWM 6","description":"\u003ch2\u003e\n Features\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Compatible with Crossfire Receivers Only\n \u003c\/li\u003e\n \u003cli\u003e\n  No 5V Regulator Built-in\n \u003c\/li\u003e\n \u003cli\u003e\n  Built-in Current Sensor\n \u003c\/li\u003e\n \u003cli\u003e\n  Failsafe Value AutoSet\n \u003c\/li\u003e\n \u003cli\u003e\n  Firmware Upgradeable\n \u003c\/li\u003e\n \u003cli\u003e\n  6 PWM Outputs\n \u003c\/li\u003e\n \u003cli\u003e\n  2 UARTS\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\n \u003cimg alt=\"\" class=\"alignnone size-full wp-image-613550\" height=\"2017\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0914\/9972\/5181\/files\/MATEKSYS-Crossfire-to-PWM-Converter-CRSF-PWM-6-Info.jpg?v=1754257115\" width=\"1000\"\u003e\n\u003c\/p\u003e\n\u003cp\u003e\n \u003cstrong\u003e\n  PINOUTS AND PADS\n \u003c\/strong\u003e\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  4v5 pad voltage = 5V pad voltage -0.3V, make sure the voltage on the 5V pad is not higher than receiver and GPS rated voltage.\n \u003c\/li\u003e\n \u003cli\u003e\n  Tx2\/Rx2(UART2) for GPS\/firmware update\/setting parameters\n \u003c\/li\u003e\n \u003cli\u003e\n  Tx1\/Rx1(UART1) for CRSF protocol Receiver\n \u003c\/li\u003e\n \u003cli\u003e\n  Vbat: Battery voltage sensing (0~36V)\n \u003c\/li\u003e\n \u003cli\u003e\n  Curr: current sensor signal (0~3.3V)\n \u003c\/li\u003e\n \u003cli\u003e\n  1~10: CH1~CH10 PWM outputs\n \u003c\/li\u003e\n \u003cli\u003e\n  G: ground\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\n \u003cstrong\u003e\n  FAILSAFE\n \u003c\/strong\u003e\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Failsafe value is set automatically after the CRSF-PWM board is powered on and receives the CRSF signal. LED blinks 8 times quickly.\n \u003c\/li\u003e\n \u003cli\u003e\n  Failsafe value = The PWM value of each channel(except CH3) when the CRSF signal is received by the CRSF-PWM board for the first time\n \u003c\/li\u003e\n \u003cli\u003e\n  CH3 is specially arranged for the throttle, Failsafe value = 988 by default.\n \u003c\/li\u003e\n \u003cli\u003e\n  Put the throttle joystick to the lowest point, put AIL(Roll), ELE(Pitch), RUD(Yaw) middle before powering on the receiver.\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\n \u003cstrong\u003e\n  LED STATUS\n \u003c\/strong\u003e\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Slow blinks: CRSF-PWM board doesn't receive a CRSF signal, e.g., the receiver is not bound with the transmitter, the receiver is not connected to UART1 of the CRSF-PWM board.\n \u003c\/li\u003e\n \u003cli\u003e\n  8x quick blinks: CRSF-PWM board received CRSF signal and failsafe value is saved.\n \u003c\/li\u003e\n \u003cli\u003e\n  2x slow blinks between 8x fast blink and solid on: CLI mode is active\n \u003c\/li\u003e\n \u003cli\u003e\n  Solid ON: CRSF-PWM board and receiver are working normally\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\n \u003cstrong\u003e\n  GPS TELEMETRY\n \u003c\/strong\u003e\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Troubleshooting for no GPS telemetry, double-check the wiring between GPS and CRSF-PWM board, some u-Blox GPS may don't output NMEA protocol, you need to be reverted GPS to the default configuration in u-center.\n \u003c\/li\u003e\n \u003cli\u003e\n  Sensors(GPS, GSpd, Hdg, Alt, Sats) will blink in the Transmitter TELEMETRY tab once the CRSF-PWM board has a connection with GPS.\n \u003c\/li\u003e\n \u003cli\u003e\n  GPS \"TX\" to CRSF-PWM board \"RX\" Single wire half-duplex UART connection, CRSF-PWM board \"TX\" to GPS \"RX\" is not essential.\n \u003c\/li\u003e\n \u003cli\u003e\n  with OpenTX Telemetry Logging, You can plot your flight path or search the lost plane.\n \u003c\/li\u003e\n \u003cli\u003e\n  u-Blox series GPS can output the \"0+1 - UBX+NMEA\" protocol by default\n \u003c\/li\u003e\n \u003cli\u003e\n  Compatible with GPS NMEA protocol, 1Hz, Baud 9600~115200\n \u003c\/li\u003e\n \u003cli\u003e\n  Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Sats\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\n \u003cstrong\u003e\n  TIM \u0026amp; PWM FREQUENCY\n \u003c\/strong\u003e\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  PWM frequency on all 10x Channels can be configured according to TIM\n \u003c\/li\u003e\n \u003cli\u003e\n  PWM runs at 50Hz by default\n \u003c\/li\u003e\n \u003cli\u003e\n  TIM3: CH5, CH6, CH7, CH8\n \u003c\/li\u003e\n \u003cli\u003e\n  TIM2: CH1, CH2, CH4\n \u003c\/li\u003e\n \u003cli\u003e\n  TIM1: CH9, CH10\n \u003c\/li\u003e\n \u003cli\u003e\n  TIM16: CH3\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\n \u003cstrong\u003e\n  CLI MODE\n \u003c\/strong\u003e\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  If the CRSF-PWM board doesn't detect GPS connected to UART2 within 10 seconds after powering on, CLI mode will active.\n \u003c\/li\u003e\n \u003cli\u003e\n  After CLI mode is active, the CRSF-PWM board can be connected to the configurator via USB-TTL module\/FC passthrough.\n \u003c\/li\u003e\n \u003cli\u003e\n  CLI mode has no effect on receiver CRSF signal and PWM outputs\n \u003c\/li\u003e\n \u003cli\u003e\n  In CLI mode, CRSF-PWM board firmware can be updated\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n Specifications\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Support: Any CRSF protocol receivers (including 433MHz, 868MHz, 915MHz, 2.4GHz)\n \u003c\/li\u003e\n \u003cli\u003e\n  Current sensor: Compatible with External (0-3.3V)\n \u003c\/li\u003e\n \u003cli\u003e\n  Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats\n \u003c\/li\u003e\n \u003cli\u003e\n  PWM frequency configurable (50Hz default, 100,160,330, 400Hz)\n \u003c\/li\u003e\n \u003cli\u003e\n  36V Max. battery voltage sense (1K:10K voltage divider built-in)\n \u003c\/li\u003e\n \u003cli\u003e\n  Rated voltage: 4~9V @5V pad, 0~36V @vBAT, 0-3.3V Curr\n \u003c\/li\u003e\n \u003cli\u003e\n  Vbat and Current sensor scale configurable\n \u003c\/li\u003e\n \u003cli\u003e\n  UARTs (for Receiver and GPS): 2\n \u003c\/li\u003e\n \u003cli\u003e\n  Size: 25mm x 16mm\n \u003c\/li\u003e\n \u003cli\u003e\n  PWM outputs: 10\n \u003c\/li\u003e\n \u003cli\u003e\n  Weight: 1.3g\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n Includes\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  1x MATEKSYS CRSF-PWM-6 Converter\n \u003c\/li\u003e\n \u003cli\u003e\n  1x Dupont 2.54 Pins\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\n\u003c\/p\u003e\n","brand":"Unmanned Tech","offers":[{"title":"Default Title","offer_id":54201817170184,"sku":"B1C-A0E-D02","price":4.45,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0982\/9043\/4312\/files\/mateksys_crossfire_to_pwm_converter_-_crsf_pwm_6mateksys-crossfire-to-pwm-converter-crsf-pwm-6-main-low_res-width-1000px.jpg?v=1775721864","url":"https:\/\/bidnamic.store\/products\/matek-crossfire-to-pwm-converter-crsf-pwm-6","provider":"Bidnamic Store","version":"1.0","type":"link"}